Boost your wireless signal with the RadioLabs Wifi Range Booster Amplifier, the easiest way to amplify and extend your wifi range. The simple plug and play design will maximize any Wifi device with an antenna jack.
The Wifi Range Booster Amplifier works by replacing the existing antenna on the wireless device in need of boosting or amplification. In the case of wireless routers and PCI or PCMCIA cards, this specially designed booster takes the signal already present in the antenna jack and amplifies it up to 15 times over (total output of 750mw, +29dBm). The Wifi Range Booster Amplifier maximizes your transmit power and receive sensitivity, turning your low power, off the shelf wireless router into a hot-rodded, high power, long range wifi router. The Wifi Range Booster Amplifier can also be used as an inline amplifier to enhance the wifi signal when connected to an external high gain antenna.
The special circuitry inside of these booster amplifiers allows them to work at 802.11B (up to 11mBps) 802.11G (up to 54 mBps) and Super G (up to 108mBps) speeds! (Click here for 300 mbps 802.11n signal amplifier) The Wifi Range Booster Amplifier will also boost your network speed if your connections are running slow because of weak signal strength. The more wifi signal available, the faster and more stable your wifi connection will be.
The Wifi Range Booster Amplifier is compatible with any 802.11 certified wireless router, access point, wifi card or PCI card with a removable antenna. This unit comes with your choice of RP-TNC or RP-SMA connectors for connecting to almost any wireless device.
Features:
Bi-directional (TX and RX) amplifier for IEEE 802.11B, G and Super G
Simply plug and play
Wide transmit input level, +7dBm to +20dBm
Low noise amplifier with system noise figure 3.5dB
Only 2 connections to boost wifi
No software or configuration needed
Compatible with any wireless device with a removable antenna
Small device footprint
RP-SMA Antenna connector for use with high gain external antennas
|
Model# WRE750MW |
Wifi Range Booster Amplifier
|
|
Operating Conditions |
Operating
Temperature Range |
Normal: +15°C ~ +35°C
Extreme: -40°C ~ +70°C |
Operating
Humidity |
5% to 100% RH |
|
Storage Temperature |
-40°C ~ +80°C |
|
Transmitter Specifications |
|
TX Input Gain |
+7dBm ~ +20 dBm |
|
TX Power Gain |
13 dB |
|
TX Linear output Power |
750 mW / +29 dBm |
|
TX/RX Switch Time |
< 1µsec |
|
User Interface |
|
Diagnosis LED
|
Power = Green
Transmit = Green
|
|
Power Requirements
|
|
DC Supply Voltage |
AC 100V~240V
50/60Hz DC 5.0v 1.0A |
|
Current Consumption |
550 mA maximum during TX |
|
Mechanical Specifications
|
|
RF Connector Type |
RP-SMA Male or RP-TNC Male (other connectors available upon request) |
|
Operating Temperature |
0 °C ~ +40 °C |
|
Electrical Conditions |
|
Access Method |
DS/TDD |
|
Operating Frequency |
2.4GHz ~ 2.5GHz |
|
Spurious Emission |
30MHz ~ 1 GHz : -36dBm(max.)
1GHz ~ 12.75 GHz : - 29dBm(max.) |
|
Package Contents |
1. Wifi Booster Unit
2. AC 110v Adapter
3. 5dBi Rubberduck antenna
4. 6 inch adapter pigtail cable |
Package Contents:
Booster Amplifier
AC Power adapter
5dBi Rubberduck antenna
6 inch pigtail adapter cable (RP-TNC included. Indicate in comments section if you need RP-SMA)
 IMPORTANT NOTE: The Wifi Range Booster Amplifier is not compatible with our High Power Access Points, Wave Magnum High Power USB Adapter, WaveRv II Long Range Adapter or any wireless device that produces over 100 milliwatts (+20dBm) output power. Connecting the WRE750MW to any device over this power level will damage the amplifier's circuitry and void all warranties. Please contact us if you are unsure of your device's power output.
|
CLEARANCE (5)
Wireless System Accessories (47)
Antennas
Remote Site Power
3G/4G Data (37)
Amplifiers & Repeaters (16)
Wireless Monitoring & Control (25)
Broadband Wireless
