Rfwel :: 3G/4G Data :: Cellular Router :: HANA SELECT Outdoor 3G/4G Router & Antenna System

HANA SELECT Outdoor 3G/4G Router & Antenna System

HANA SELECT now allows combining high-gain outdoor Cellular/WiMax antennas with router and removes the need of purchasing an outdoor antenna kit in addition to 3G/4G router. This makes much more sense especially when outdoor antenna mounting location is far from network connection point such that it would require long lossy coaxial cables to indoor CPE/modem (it is much easier and cheaper to run 100ft of CAT5E cable than 100ft of LMR-400 coaxial cable).

The HANA Max solves the most common problems encountered with mobile 3G/4G router deployment including:

Signal strength/throughput – 13 dBi directional antenna locks in the signal – especially in beneficial for WiMax where the 2.5-2.7GHz band used by N. American WiMax providers has much worse in-building penetration capability than cellular/PCS bands.
Physical modem Security – HANA’s radome cover locks in the USB modem.
Flexibility of Placement – using POE allows the router and USB/Express modem to be placed where signal is best and router is out of the way (air plenum rated for above suspended ceiling, outdoor with NEMA kit, etc..)
Easy Installation – HANA’s “all-in-one” design allows for easy installation with 1 CAT 5 cable connection and 4 screws on the mounting bracket (if necessary). The signal strength meter on the user interface allows for easy site placement and antenna tuning.
Enterprise Class Features – HANA’s onboard BC2 router provides all the necessary advanced routing features like SNMP, SSH/CLI, Open WRT, VPN IP Pass through.

Technical Specifications

Nexware Features

XtremeSpeed® WAN Optimization
IPsec Termination & GRE (Generic Routing Encapsulation)
VRRP (Virtual Router Redundancy Protocol)(No single point of failure)
WDS (Wireless Distribution System)
Auto Failover w/Anti-Flap

Network Features

	DHCP Server		Virtual server
	DNS Relay		MAC access control
	DMZ Host		Dynamic IP
	Auto-Reconnect		Auto-Disconnect
	Connect-on-demand		Static IP / RIP IP
	Supports cable modems, DSL, wireline WAN, T1, & 3G WAN Auto Failover to 3G for redundancy		QoS

Management

OMA-DM
SNMP Management
Supports SSH and Telnet
Firmware upgradeable
Auto connect to network

Ports

1*ExpressCard Slot
1*USB 2.0
(1) 10/100 WAN (Software Configurable)
(1) 10/100 LAN

Protocol Standards & OS Support

IEEE 802.11 b/g/n (WiFi) w/ 2x2 MIMO (2.4-2.462 GHz CCK) - up to 300Mbps
IEEE 802.3 (100Mbps Ethernet)
IEEE 802.3u

Security

64-bit and 128-bit WEP encryption
WPA encryption w/ WPA2 support
NAT (Networks Address Translation)
VPN IPsec Pass Through
VPN IPsec Termination

Environmental

Temperature 0~40oC
Humidity 10%~90% non-condensing

Electrical Specifications

Power Supply

Switching 12V, 1.25A. Can easily operate from outdoor solar/PV system or with outdoor backup UPS.

Frequency Range

3G: 824-1900 MHz
4G: 2500-2700 MHz

Gain

3G: 9.3dBi
4G: 12dBi

3dB Beamwidth (AZ/EL)

3G: 91°/59° - 800MHz, 60°/50° - 1900MHz
4G: 35°/35° - 2600MHz

Polarization

Horizontal or Vertical ** (note that when mounting outdoors need to have HANA mounted vertically to minimize risk of water ingress through ports on the underside which restricst the polarization options available)

VSWR

<2.5:1 (measured at end of attached pigtail connectors)

Front-to-Back Ratio

30dB

Cross-Polarization Discrimination

25dB

Antenna Connector

Pigtails w/ FME-Male ends provided for modem attachment.

What's Included: