Wireless Thermostat & Receiver Combo

Did you ever wish you could turn up the heat without getting out of your warm cozy bed? Or that you could turn down the air conditioning from your living room chair? Or put the thermostat in a newborn baby's room to keep the temperature exactly right? If you wish to be able to move the thermostat, put it by your bedside at night, or even control your heating and air conditioning system from two different places, such as upstairs and downstairs, then the Totaline Wireless Thermostat is for you.

Here's how it works: Remove your old wall thermostat, replace it with the Totaline receiver and then remotely control the temperature anywhere in your house with the Totaline thermostat. Add additional wireless thermostats (see below) around your house (up to 4) and have instant access to temperature control no matter where you are.

Specifications

This kit consists of two parts, a thermostat and a receiver. The thermostat is a wireless, battery operated unit that can be placed in any location in your home (up to 500ft. from receiver) and will transmit radio signals to the receiver which replaces your existing wall thermostat. This thermostat allows up to 4 time/temperature settings to be programmed per 24-hr period and stores programs for 7 independent days.

Place Receiver Wherever Wires Are Available
The receiver is easy to install and is wired just like a standard 24VAC thermostat. Connect the unit wherever existing wires are available; the old thermostat location, in a furnace closet, in an attic or basement.

Place Thermostat in Most Important Rooms
Once the receiver is installed, the thermostat can then go anywhere in the building, and it will transmit radio signals back to the receiver. The transmission range is up to 500 feet, and it works through walls, floors, ceilings, etc. The temperature sensor is located on the thermostat, so place the thermostat where temperature control is most important to you — your bedroom, the boss's office, a baby's room, etc. The thermostat runs off of 2 AA lithium batteries (included).

If more than one transmitter is used with a single receiver, the transmitters must be given different Unit ID Numbers. Only the transmitter with Unit ID Number 1 may have a programmed schedule or be configured. All configuration parameters are taken from the transmitter with Unit ID Number 1. Transmitters with Unit ID Numbers 2, 3, and 4 cannot be programmed or configured (except for set points).

When more than one transmitter is used, the receiver will only accept commands
from the transmitter that was last used (button pressed). All other set points and modes from other transmitters are ignored. If the transmitter with Unit ID Number 1 has a schedule and is in Program On mode, the receiver will revert back to following the programmed schedule when a time period change occurs, even if the transmitter with Unit ID Number 1 is not the current commanding transmitter.

• Auto Changeover, 2-Stage Heat & 2-Stage Cool for use with gas / electric or heat pump systems.
• Thermostat is completely wireless, receiver can be mounted at unit or at old thermostat's location.
• Transmits at 418MHz using pulse code modulation — won't interfere with other wireless systems
• Sender uses two AA batteries (included)
• 7 Day Programmable with 4 time periods per day, copy command and holiday mode
• Dual-setpoint with adjustable deadband (1 to 6 degrees) and temperature sensor calibration.
• All programming stored in nonvolatile memory.
• Thermoglow Electro-luminous Display.
• Display shows heat and cool setpoints, mode, and room temperature simultaneously.
• 5 minute compressor time guard and adjustable cycle limit, both overrideable for servicing equipment
• Setpoint adjustment range from 35° to 99° F, sensing range from 32° to 99° F.
• 64 house codes allow installation of up to 64 systems within transmit range with no interference.
• On board dry contact closure available to force thermostat into occupied operation.
• Meets California Commercial Title 24.

** If you have a 2-wire heat system you will need a 2-wire kit here. See forums for technical discussion on this. For additional installation assistance please contact a support specialist.

Contact us for selection or installation assistance or if you can't find the product or options you need. Rfwel is a licensed low voltage communication contractor AZ Registrar of Contractors Number 253407